Once you have a blog, you need to become the voice of authority. One way to do this is by writing trustworthy instructions so blog readers can perform a skill or process. You will select a blog-related subject that you can write and post the instructions for your readers. Use the planner to create your post. This should include the following items:
- An introduction section
- A list of needed materials
- A step-by-step process for performing the task, with no missing/out of order info
- A warning/caution section
- A conclusion
This comment has been removed by the author.
ReplyDeleteGraphic Design is fun to learn it would will help you to get a job or career of it. Is easy to learn the right stuff if you follow the right instruction.
ReplyDeleteNeed the computer that can run i prefer building it.
Adobe photoshop software
Need a lot of time
Need a photo and made back up too
Be super organized
Tern on your computer
Open adobe photoshop
Find the photo where you put it
Start editing and make a folder it’s important
Add folder should be by layer section
Start editing!
Make sure you backup your files some time the program crashes.
At the end of these step you should finish your first high quality picture. If you miss a step or done get it you can follow us on our blogs
I like your blog you have good steps and I feel like I would be able to do it.
Deletesome better grammar to make it sound less confusing would help, but, the key points of being a graphic designer seems spot on for what you will need and the requirements you will need to have.
DeleteTry to make it a little bit easier understand.
DeleteI'm going to be teaching you the proper way to cast your fishing pole so you can cast farther. Whether or not you are a professional or a beginner it is important to have good technique and following these steps could help you.
ReplyDeleteTo prepare you for this you will need
-Fishing rod
-Reel
-Lure
-Line
Steps:
1 Grab the fishing pole
2 Look for a open spot where you are gonna cast
3 Put hand on reel
4 Open release
5 Whip it out there
6 Let go of line half way
7 Now close the release
8 Reel It in.
Make sure you got space so nobody hooks you or whacked in the face by the fishing pole.
Following these steps will help you fix your casting and hopefully help you catch more fish.
good description on how to fish, but it could would not hurt to add a little more beef to the post.
DeleteI like your blog but can you explain little bit more about the step because if i'm not a not a fishing guy what is [reel].
DeleteOkay, today I am going to tell you guys and gals how to replace brakes on a car with disc brakes. I’m going to have to tell you to please use your imagination and your car for this one. It will make it easier.
ReplyDeleteTo start off,you’ll want to take a tire iron and use it to loosen the lug nuts or lug bolts on your vehicle, take not to only loosen the wheel on the side you’re replacing brakes on! After that, you will want to jack up the car on its lift spot underneath the car, then use a jack stand by the lifting spot to prevent the car from falling down when you’re crouched in the wheel well! That would be “no bueno”!
Now since you got your wheel of, it is time to get those calipers off to replace the brake pads. Start by taking your messy and unorganized tool box and look for the proper sized wrenches to fit over the bolts for the caliper bolts. You might cuss and question yourself where the tools you need are, but you’ll find them eventually after dumping the tool box out and remembering you left them in the house. Start loosening the bolts, should be 2 bolts per caliper. Once removed, pull the caliper off the caliper carrier assembly. You can then pull out those old, and deformed brake pads you wanted to change last year. Take them out. Next, loosen bleed valve on caliper, then use a large C clamp and place it so it will squeeze the piston on the caliper back into the caliper so the new pads will fit nice and snug. This is the worst part of the job, prepare to have brake fluid drizzle all over your hands and pants. Make sure to keep a towel handy to cleanup the mess.
the caliper piston retracted, and the bleed valve tightened, it is time to place in the new pads! Take a new pad and put it into place, along with the other pad for that side. Once in place you can line the caliper back in its place and start putting the caliper bolts back on. Once finished, you’ll want to bleed the brakes, again. Loosen bleed valve and press it until the pedal starts getting more firm. Tighten bleed valve.
Start to put wheel back on car by lining up holes and lug studs/hub. Hand tighten lugs and then in a star pattern, tighten them down to factory torque specs so it will be safe to drive on. Last thing you want after replacing brakes is a wheel going flying off your car on the highway, but if you feel your car wiggling you better stop immediately and tighten that wheel lugs tighter than before.
Now with your wheel safely on, you will want to jack your car up to remove the jack stand from under your car, once done lower the jack and car and remove jack from under your car. Then get in your car and drive around the block to feel how the brakes work before taking them on the main busy roads and risk your life and other people’s lives.
Hope this tutorial was helpful for you!
Follow the format a little better try to make a little bit shorter.
Deleteyou have a good instruction, but is little confusing if you look over the page and lost track where you were wile fixing your car that would be nice if it shorter.
Delete